Andy's 91' 80q

Document and share your build!

Re: Andy's 91' 80q

Postby rennenmsports » Tue Mar 31, 2020 3:03 pm

Well. I got the rieger b4 rs2 abs plastic replica front bumper on finally. The b4 90 fenders I got make it fit so much better then the b3’s.
14F938AB-091E-43C6-A34B-0AECEAAB26F1.jpeg
14F938AB-091E-43C6-A34B-0AECEAAB26F1.jpeg (78 KiB) Viewed 13175 times
rennenmsports
 
Posts: 94
Joined: Jan 15, 2017

Re: Andy's 91' 80q

Postby PRY4SNO » Tue Mar 31, 2020 3:56 pm

Nice!

Gonna need a profile and 3/4 shot to see more about the bumper--->fender transition.
Find me on Instagram @pry4sno

|| 2010 Golf Sportwagen TDI /// #farmenwagen
|| 2002 Dodge Ram 2500 24vt 4x4 #bertancummins
|| 1992 80 quattro 20v /// Eventual AAN'd Winter Sled
|| 1990 Coupe quattro /// Because Racecar
User avatar
PRY4SNO
 
Posts: 2385
Joined: Mar 3, 2013
Location: Edmonton, AB

Re: Andy's 91' 80q

Postby rennenmsports » Wed Apr 01, 2020 8:31 am

AA1D0DAB-626E-4AC0-AEEA-E0BD30964680.jpeg
AA1D0DAB-626E-4AC0-AEEA-E0BD30964680.jpeg (21.61 KiB) Viewed 13158 times

B0B36F44-8F98-4471-A46A-6D49C9E0310D.jpeg
B0B36F44-8F98-4471-A46A-6D49C9E0310D.jpeg (23.62 KiB) Viewed 13158 times

F185F88D-77F2-48DB-98BE-3834C23A2F45.jpeg
F185F88D-77F2-48DB-98BE-3834C23A2F45.jpeg (26.83 KiB) Viewed 13158 times

Ignore the crappy spray paint job on the fenders
rennenmsports
 
Posts: 94
Joined: Jan 15, 2017

Re: Andy's 91' 80q

Postby DE80q » Wed Apr 01, 2020 9:05 am

I gotta say, it looks quite funny with the 14" wheels still on it. Otherwise looking very nice
"If you can't find one, make one"

Dallastown, PA
1991 Audi 80 quattro (10vt project)
1991 Audi Coupe Quattro (project: my first 20v)
2007 Mitsubishi Raider(Dakota in disguise)
2019 Chevy Cruze RS hatch (wife's little red sporty car)
DE80q
 
Posts: 2518
Joined: Mar 4, 2013
Location: York PA 17403

Re: Andy's 91' 80q

Postby rennenmsports » Wed Apr 01, 2020 9:43 am

I do have these
112D5C19-2DF6-4256-B5E5-26E6D75E4576.jpeg
112D5C19-2DF6-4256-B5E5-26E6D75E4576.jpeg (26.82 KiB) Viewed 13154 times
rennenmsports
 
Posts: 94
Joined: Jan 15, 2017

Re: Andy's 91' 80q

Postby PRY4SNO » Thu Apr 02, 2020 2:20 am

Not bad from here, those Reiger bumpers have always been well regarded. Also, have had a soft spot for Turbo Twists on Coupes for exactly one forever.
Find me on Instagram @pry4sno

|| 2010 Golf Sportwagen TDI /// #farmenwagen
|| 2002 Dodge Ram 2500 24vt 4x4 #bertancummins
|| 1992 80 quattro 20v /// Eventual AAN'd Winter Sled
|| 1990 Coupe quattro /// Because Racecar
User avatar
PRY4SNO
 
Posts: 2385
Joined: Mar 3, 2013
Location: Edmonton, AB

Re: Andy's 91' 80q

Postby rennenmsports » Thu Apr 02, 2020 9:26 am

Thanx man! I think the rears are too wide to work. But I might be able to use 4 fronts. I’m looking for wheel part# 993 362 134 06. Will 18x7.5 wheels work on a b3 without rubbing?
rennenmsports
 
Posts: 94
Joined: Jan 15, 2017

Re: Andy's 91' 80q

Postby PRY4SNO » Thu Apr 02, 2020 2:50 pm

Depends on the et and what brake/hub setup you're running. Also, some tyres are effectively +1 size based on contact patch compared to others. I know it was a bit of a shock when I installed some Dunlop Direzza Sport Star Specs after my hub/brake swap.
Find me on Instagram @pry4sno

|| 2010 Golf Sportwagen TDI /// #farmenwagen
|| 2002 Dodge Ram 2500 24vt 4x4 #bertancummins
|| 1992 80 quattro 20v /// Eventual AAN'd Winter Sled
|| 1990 Coupe quattro /// Because Racecar
User avatar
PRY4SNO
 
Posts: 2385
Joined: Mar 3, 2013
Location: Edmonton, AB

Re: Andy's 91' 80q

Postby rennenmsports » Sun Apr 19, 2020 7:18 pm

PRY4SNO wrote:Depends on the et and what brake/hub setup you're running. Also, some tyres are effectively +1 size based on contact patch compared to others. I know it was a bit of a shock when I installed some Dunlop Direzza Sport Star Specs after my hub/brake swap.

Ok. Thanx. I’m still debating. Long time till it’s ready for that

I was able to rust proof the rear subframe and get all the bushings and mounts in. Also I used the same pcv elbow I used for the trans breather on the rear diff breather too. Can’t go down so I removed the gas tank and found a spot behind it too drill the hole.
4E348775-A00A-4740-80B3-68DEE23EA778.jpeg
4E348775-A00A-4740-80B3-68DEE23EA778.jpeg (22.63 KiB) Viewed 11854 times

2D8618BA-0B08-45BF-A0CE-BD92378A626F.jpeg
2D8618BA-0B08-45BF-A0CE-BD92378A626F.jpeg (18.56 KiB) Viewed 11854 times

0CBEADEA-F5E2-43D1-840C-F3D5F122CF8C.jpeg
0CBEADEA-F5E2-43D1-840C-F3D5F122CF8C.jpeg (105.94 KiB) Viewed 11171 times
Last edited by rennenmsports on Fri Apr 24, 2020 9:29 pm, edited 1 time in total.
rennenmsports
 
Posts: 94
Joined: Jan 15, 2017

Re: Andy's 91' 80q

Postby rennenmsports » Fri Apr 24, 2020 1:23 pm

Got the oil coolers in place with one mount each and good ole painters tape. It looks better now with the bumper on. I used two Setrab 50-616-7612 coolers. Barely fit behind the bumper.
4F999181-FA60-4AE5-9F46-8D815675E7A7.jpeg
4F999181-FA60-4AE5-9F46-8D815675E7A7.jpeg (98.17 KiB) Viewed 11242 times
rennenmsports
 
Posts: 94
Joined: Jan 15, 2017

Re: Andy's 91' 80q

Postby PRY4SNO » Fri Apr 24, 2020 2:28 pm

Why two oil coolers?
Find me on Instagram @pry4sno

|| 2010 Golf Sportwagen TDI /// #farmenwagen
|| 2002 Dodge Ram 2500 24vt 4x4 #bertancummins
|| 1992 80 quattro 20v /// Eventual AAN'd Winter Sled
|| 1990 Coupe quattro /// Because Racecar
User avatar
PRY4SNO
 
Posts: 2385
Joined: Mar 3, 2013
Location: Edmonton, AB

Re: Andy's 91' 80q

Postby rennenmsports » Fri Apr 24, 2020 3:35 pm

PRY4SNO wrote:Why two oil coolers?

One for the engine and the other is either for the engine or transmission. But for now my transmission is looped with no cooler. Not sure how hot these engine oil temps get under heavy use especially since it’s 95 degrees down here right now. The air gap under the intercooler is for the trans cooler if it gets to that point.
rennenmsports
 
Posts: 94
Joined: Jan 15, 2017

Re: Andy's 91' 80q

Postby vt10vt » Fri Apr 24, 2020 4:02 pm

Those coolers look awesome in the bumper openings, well done.
-Shawn C.
2001 S4 6spd Avant blk/blk - stock daily
2002 01E B6 A4 Built FYF, Built 1.8T, HX35 ~330whp
1989 MC-1 200 Avant- MS1 -Gone but will never forget her lessons
1987 5ktq Sedan - Best $500 beater ever
User avatar
vt10vt
 
Posts: 1012
Joined: Mar 11, 2013
Location: Winooski, VT

Re: Andy's 91' 80q

Postby rennenmsports » Fri Apr 24, 2020 4:42 pm

vt10vt wrote:Those coolers look awesome in the bumper openings, well done.

Thank u very much! I was going for looks hoping for overkill. It took me a while to find ones that cover the openings nicely.
66F7FA2F-17CC-49E1-871C-BA65F230BE2A.jpeg
66F7FA2F-17CC-49E1-871C-BA65F230BE2A.jpeg (97.61 KiB) Viewed 11217 times

F34E037B-805F-46D7-837B-53E8BB35EA41.jpeg
F34E037B-805F-46D7-837B-53E8BB35EA41.jpeg (77.47 KiB) Viewed 11217 times
rennenmsports
 
Posts: 94
Joined: Jan 15, 2017

Re: Andy's 91' 80q

Postby rennenmsports » Wed Sep 02, 2020 5:39 pm

Mini Cooper electric power steering pump
691B0528-9C8F-4151-BF0D-DFA3BD42B821.jpeg
691B0528-9C8F-4151-BF0D-DFA3BD42B821.jpeg (270.09 KiB) Viewed 2595 times

ED95C390-4CC3-4507-8028-10BFBE098D43.jpeg
ED95C390-4CC3-4507-8028-10BFBE098D43.jpeg (224.21 KiB) Viewed 2595 times
Attachments
363C2746-72DF-47D1-9E23-0E1532249D6C.jpeg
363C2746-72DF-47D1-9E23-0E1532249D6C.jpeg (270.09 KiB) Viewed 2595 times
rennenmsports
 
Posts: 94
Joined: Jan 15, 2017

Re: Andy's 91' 80q

Postby rennenmsports » Mon Sep 07, 2020 1:48 pm

FC756C34-2675-4183-B421-5A0186190042.jpeg
FC756C34-2675-4183-B421-5A0186190042.jpeg (298.7 KiB) Viewed 2502 times

Getting closer to finishing the front end. Everything added is just tac welded right now. All I need is the trans cooler and it’s finished
rennenmsports
 
Posts: 94
Joined: Jan 15, 2017

Previous

Return to Projects

Who is online

Users browsing this forum: Majestic-12 [Bot] and 13 guests

cron